GlossaryDrainage technical term

Top-hat profile

Also: Lateral connection seal, Top-hat sleeve, Top-hat rehabilitation

A top-hat profile is a rehabilitation component for the junction between a main sewer and a pipe joining it from the side. It is installed from the inside, cures in the pipe and seals the junction tightly. This repairs one of the most sensitive points of the sewer system without digging up the road or the garden.

Wastewater pipe being rehabilitated with a CIPP liner without digging, with connections then sealed with top-hat profiles

In brief

A top-hat profile is a hat-shaped, resin-impregnated moulding that seals the connection of a lateral to the main sewer from the inside. The brim sits against the main pipe and the cylinder extends into the lateral. It is installed with a robot and cures in the pipe – typically after CIPP lining or where junctions leak.

What is a top-hat profile?

Wherever one pipe joins another, there is a junction: a house connection meets the municipal sewer, a soil stack or floor drain meets the underground drain. These junctions are often the weakest point of the entire drainage system, because they used to be made by hand and sealed only with mortar.

The top-hat profile closes precisely this junction. It consists of a carrier material, for example a glass-fibre or felt fabric, which is impregnated with resin. Its shape resembles a hat: the flat brim lies against the inner wall of the main pipe around the opening, and the tubular part extends some way into the lateral. Once cured, it forms a seamless, watertight connection.

When is a top-hat profile used?

The most common reason is CIPP lining of the main sewer. After the robotic cutter has reopened the sealed connections, a gap remains at the junction between the new liner and the old lateral. The top-hat profile covers it and connects the liner tightly to the lateral.

A top-hat profile is also used without prior rehabilitation of the main pipe, for example when a CCTV drain survey shows cracks, broken-out mortar, roots or groundwater ingress at a junction. With laterals under roads in particular, this saves an expensive trench on public land.

How installation works

First, the main sewer and the connection are cleaned and examined by camera. The robotic cutter removes roots, deposits and protruding edges so that the brim fits tightly. The top-hat profile is then impregnated with resin on site and mounted on a special packer.

A robot moves the packer through the main sewer to the junction, aligns it precisely with the opening under camera supervision and inflates it. The cylinder turns out into the lateral and the brim presses against the wall of the main pipe. Depending on the system, the resin cures at ambient temperature, with heat or with UV light. The packer is then removed and the result checked with the camera.

Advantages of the top-hat profile

The top-hat profile repairs the junction without excavation, without prolonged traffic disruption and without reinstating surfaces. The connection is back in service after a short time. Because it is jointless and the resin forms a smooth surface, deposits do not build up and roots cannot find a way into the pipe.

A watertight connection also prevents groundwater from entering the sewer as infiltration water or wastewater from escaping into the ground. This relieves wastewater treatment and protects groundwater – an aim that the Water Protection Act also pursues.

Limitations and requirements

A top-hat profile requires a main sewer in which the robot can travel and work with the packer. This is not possible in very small pipes. The connection must also have a shape the profile fits; badly offset or collapsed junctions may have to be renewed using open-cut construction.

How well the seal holds depends largely on the preparation. Thorough cleaning, careful cutting and exact positioning are crucial. After installation, a leak-tightness test of the connection can confirm the quality.

Practical example

In a municipality in the Zurich Oberland, the public sewer of a residential street was rehabilitated with a CIPP liner. One property owner took the opportunity: her lateral joined the sewer with broken-out mortar and water seeping in. After cutting open the opening, the team installed a top-hat profile that connected the new liner tightly to her pipe. The road was left untouched and the connection was back in service the same day.

Matching services from Karo Kanaltechnik

Further reading in our guides

Top-hat profile: frequently asked questions

What is a top-hat profile needed for?+

To make the connection between the main sewer and a lateral watertight. It is mainly used after CIPP lining or where junctions are leaking, root-infested or broken out.

Does a top-hat profile require digging?+

No. The top-hat profile is installed with a robot from the main sewer. Access via an existing manhole is required, but no trench.

What is the difference between a top-hat profile and a patch liner?+

A patch liner repairs a section of a straight pipe, for example a crack or a leaking joint. The top-hat profile is shaped specifically for the junction where a lateral joins the main sewer.

How long does it take to install a top-hat profile?+

For a single connection, usually just a few hours including preparation and curing. The exact time depends on the resin system, the condition of the connection and the preparatory work.

Top-hat profile in your region?

We are there for you across German-speaking Switzerland – fast, clean, with a 24/7 emergency service.