GlossaryDrainage technical term

Robotic cutter

Also: Sewer robot, Sewer cutting robot, Rehabilitation robot

A robotic cutter, often simply called a sewer robot, is a compact, remote-controlled vehicle that works inside a wastewater pipe. It carries a swivelling cutting head and a camera and is controlled by the operator on a monitor in the service vehicle. It makes it possible to carry out work inside the pipe that would once have required digging.

Technician controlling the work in the pipe and checking the image on the camera monitor

In brief

A robotic cutter is a remote-controlled device with a camera and a rotating cutting head that works inside sewers. It removes roots, hard deposits and protruding pipe stubs, reopens the lateral connections after CIPP lining and prepares them for a top-hat profile. This makes precise repairs inside the pipe possible without digging.

What is a robotic cutter?

The robotic cutter is a tool carrier on wheels or tracks that is lowered into the pipe through a manhole. A cutting head mounted on an arm can rotate, lift, lower and swivel. Depending on the system, it is driven electrically, hydraulically or pneumatically. A camera on the unit transmits the image to the vehicle, where the operator controls every movement.

Robotic cutters are mainly used in larger pipes where the unit has enough room to travel and work, for example in underground drains, collecting sewers and public sewers. For small house drains there are compact cutting tools on flexible shafts or drain snakes that work on the same principle.

What is a robotic cutter used for?

A classic use is clearing obstructions that jetting cannot shift: dense root masses, hard encrustation of limescale or concrete, hardened grease deposits. The cutting head removes them flush with the pipe wall without damaging the pipe.

Just as often, the robot removes protruding connections. If a lateral inlet was once inserted too far into the main sewer, the pipe stub projects into the cross-section and catches solids. The robot cuts it off flush. Protruding edges at joints or concrete residues can also be removed in this way.

Indispensable in CIPP lining

When a sewer is rehabilitated with a CIPP liner, the new liner initially also seals off all the lateral connections. So that wastewater from the connected properties can drain again, these openings have to be cut open again from the inside. This is the robotic cutter’s most important task in rehabilitation.

Before installation, the position of each connection is measured precisely with the camera. Once the liner has cured, the robot travels to the positions, locates the dimple in the liner and cuts the opening cleanly. The edges are then smoothed so that nothing gets caught. This is often followed by a top-hat profile, which additionally seals the junction between the main sewer and the lateral.

Preparation for patch liners and top-hat profiles

The robotic cutter is also needed before localised repairs. A patch liner must fit tightly against a clean pipe wall. Obstructions, offsets with sharp edges or deposits at the defect are therefore cut away beforehand.

For a top-hat profile, the connection area is cleared and smoothed all round so that the brim of the hat fits tightly against the wall of the main pipe. The cleaner this preparation, the longer-lasting the seal.

Advantages and limitations

The biggest advantage is obvious: work that used to require a trench, barriers and reinstatement of surfaces is done by the robot from the manhole. This saves time, protects gardens and roads and shortens the time the pipe is out of service.

Limits are set by the diameter, bends and the condition of the pipe. In very narrow pipes there is no room for the robot, and with collapsed pipes or severe fragmentation, working from the inside is no longer safe. Whether a robot can be used is therefore always clarified first by a CCTV drain survey.

For owners and property managers this means: not every blocked or root-infested pipe has to be replaced. Obstructions can often be removed with the robot and the pipe then rehabilitated from the inside, either locally or along its full length.

Practical example

In Schlieren, a team rehabilitated a 40-metre underground drain beneath a commercial building with a CIPP liner. Six lateral connections from soil stacks and floor drains were initially sealed off as a result. Their positions had been measured by camera before installation. After curing, the robotic cutter travelled to the locations, cut the openings cleanly and smoothed the edges. By the evening of the same day, the building’s drainage was back in operation.

Matching services from Karo Kanaltechnik

Further reading in our guides

Robotic cutter: frequently asked questions

Does the robotic cutter damage the pipe?+

No, not if it is used properly. The operator controls every movement under camera supervision and chooses the cutting head to suit the material. Only obstructions and deposits are removed, not the pipe wall.

From what diameter can a robotic cutter work?+

That depends on the unit. Classic robotic cutters need enough room to travel and mainly work in underground drains and collecting sewers. For smaller house drains there are compact cutting tools on shafts or drain snakes.

Why is a robotic cutter needed after CIPP lining?+

During installation the liner seals off all the lateral connections. The robot then reopens them from the inside so that wastewater from the connected pipes can drain away.

Can a robotic cutter remove roots?+

Yes, that is one of its most common jobs. It cuts root masses off flush with the pipe wall. To stop them growing back, the entry point should then be sealed with a patch liner or CIPP liner.

Robotic cutter in your region?

We are there for you across German-speaking Switzerland – fast, clean, with a 24/7 emergency service.