What is a manhole cover?
A manhole cover is the cover of a drainage chamber: an inspection chamber, a silt trap, a pump chamber or an access chamber. Specialists usually speak of a chamber cover, because it consists of two parts – the frame, which is firmly set on the chamber neck or a seating ring, and the actual lid, which lies in this frame and can be lifted out.
The cover has several tasks at the same time. It protects people and animals from falling in, prevents leaves, soil or gravel from getting into the chamber, keeps odours in the sewer and transfers the loads from pedestrians and vehicles to the chamber structure. At the same time, it is the door to the pipe network: through the open chamber, pipes are jetted, surveyed with the camera and tested for leak-tightness.
Materials: cast iron, concrete, plastic and steel
Cast iron is the classic. Manhole covers made of grey cast iron or ductile cast iron (spheroidal graphite iron) are very strong, durable and available in all load classes. They are found in roads, driveways and car parks as well as on forecourts. For the same load-bearing capacity, ductile cast iron is usually lighter than grey cast iron, which makes it easier to open.
Concrete covers and covers with a concrete infill in a steel or cast iron frame are heavy and inexpensive. They are often found at older properties and in gardens. Their drawback: the edges can spall, and a heavy concrete cover can hardly be lifted without lifting tools.
Plastic covers made of polypropylene or polyethylene are light and corrosion-free. They are suitable for pedestrian areas and gardens, typically in classes A15 and B125, and often sit on plastic chambers with a telescopic top section. In driveways used by cars or vans, they are only permitted if they have been explicitly tested for the corresponding class.
Covers made of steel or aluminium are used mainly in buildings, underground car parks and courtyards. A special form is the recessed cover, also called an infill cover: a shallow tray that is filled with the same surfacing as the area around it. This keeps the chamber almost invisible – but it must remain findable, for example through a marking or an entry in the drainage plan.
Load classes according to EN 124: A15 to F900
The load a chamber cover must bear is governed by the European standard EN 124, which applies in Switzerland as SN EN 124. Since 2015 it has been divided into several parts: Part 1 contains the general requirements, while the other parts cover the individual materials such as cast iron, steel and aluminium, reinforced concrete, composites and plastics. The standard divides covers into six classes according to where they are installed. The number after the letter is the test load in kilonewtons – that is, the load the cover must withstand in the test, not the permanent load in everyday use.
A15 (test load 15 kN): areas used only by pedestrians and cyclists, such as garden paths and lawns. B125 (125 kN): footways, pedestrian zones and comparable areas as well as parking areas and car park decks for cars. C250 (250 kN): kerbside channels and edge areas along the carriageway, as well as verges. D400 (400 kN): road carriageways, hard shoulders and parking areas for all types of road vehicles. E600 (600 kN): non-public traffic areas with high wheel loads, such as industrial and port areas. F900 (900 kN): areas with particularly high wheel loads, for example airfield pavements.
For properties, this means in practice: in the garden, A15 is usually sufficient; on an area where a car is occasionally parked, at least B125 is needed; in a driveway also used by lorries, heating oil deliveries or a jetting vehicle, D400 is the safe choice. If in doubt, go one class higher. An under-designed cover can crack or deform under load or, in the worst case, collapse. The class is cast or stamped into the cover, together with a reference to the standard and the manufacturer's mark. For access chambers, the standard also requires a clear opening of at least 600 mm so that people can climb in with equipment.
Round or square manhole covers?
Round manhole covers have a decisive safety advantage: a round cover cannot fall through its own opening into the chamber, no matter how it is turned. It does not need to be aligned when closing and distributes the load evenly over the frame. That is why round cast iron covers are the norm in roads and driveways.
Rectangular or square covers fit better with paving, slab surfaces and building edges and are therefore popular for forecourts, terraces and indoors. They must be designed to prevent them from falling in, for example with a seating that is wider than the diagonal of the opening, or with hinges. If you are replacing a square cover, you should measure the dimensions, frame and class precisely, because square covers are less standardised than round ones.
Odour-tight and ventilated chamber covers
If there is a smell of sewage around a manhole, the cover is often to blame. Chamber covers are available in closed and in perforated, ventilated designs. Perforated covers let air and, depending on the design, surface water through; they are found mainly on chambers for rainwater and yard water. A chamber through which foul water flows, on the other hand, needs a closed cover that is as odour-tight as possible and has a seal.
With odour-tight covers, a seal running all the way round between the lid and the frame ensures that no sewer air escapes. If this seal has hardened, is dirty or is missing, odour escapes – especially in warm weather and if the pipe is poorly ventilated. If the smell persists even though the cover is intact, it is worth looking at the vent pipe and the water seal traps in the house; the cover is then merely the place where the problem becomes noticeable.
Cover rattles or does not sit properly: causes and remedies
A rattling manhole cover is more than a nuisance. Every time a vehicle passes over it, the lid knocks against the frame, the seating surfaces wear further and the frame works loose in its mortar bed. Common causes are dirt, sand or small stones in the seating, a worn or missing cushioning insert, a lid that does not match the frame, or a frame that no longer sits firmly because of cracked mortar or a subsided chamber neck.
Often it is enough to clean the seating thoroughly and fit a new cushioning insert. If, on the other hand, the frame itself wobbles, it must be removed and reset in mortar on a load-bearing seating ring. If the lid or frame is worn out, cracked or does not match the other, replacing the complete cover is the lasting solution. A loose or subsided cover is also a sign that the chamber neck underneath may be damaged – this should be checked at the same time.
Bringing a manhole cover to the right level when redesigning a garden or forecourt
When a garden is relandscaped, a forecourt is paved or a driveway is asphalted, the level around the chamber often changes. The cover then sits too low and becomes a trip hazard or a puddle, or it sticks up and gets caught by the lawnmower or snowplough. The wrong solution is simply to cover over the lid. The right one: adjust the frame and cover to the new level.
With concrete chambers, this is done with seating or adjustment rings under the frame that raise the chamber neck, or by removing material if it needs lowering. Plastic chambers often have a telescopic section that can be adjusted in height. In any case, the frame must then sit firmly over its full surface again so that the loads are transferred cleanly into the chamber. If the use also changes with the redesign – the lawn becomes a parking space – the load class must be checked at the same time and the cover replaced if necessary.
Accessibility: do not cover manhole covers
An inspection chamber only serves its purpose if its cover can be found and opened. Property drainage according to SN 592 000 requires accessible inspection chambers, and the wastewater regulations of many municipalities require chambers to remain accessible at all times. As a rule, the owner is responsible for the maintenance of private chambers.
In practice, however, manhole covers regularly disappear under lawns, gravel, planters, wooden decks or new paving. In the event of a blockage or backflow, the cover first has to be found and uncovered, which costs time and money. If you want a chamber to disappear visually, it is better to use a recessed cover and record its location in the drainage plan rather than building over it.
Replacing the manhole cover as part of a manhole rehabilitation
A damaged cover is rarely a chamber's only problem. Subsided frames, cracked chamber necks, leaking joints between the manhole rings and corroded walls often occur together. That is why it is worth combining the replacement of the cover with a manhole rehabilitation: the chamber is cleaned, its condition recorded, the chamber neck and walls repaired, and finally a new cover in the appropriate load class is set at the right level.
Karo Kanaltechnik rehabilitates inspection chambers together with chamber covers and chamber necks. Before the rehabilitation, the chamber is cleaned and its condition documented with photos so that it is clear whether only the cover or the chamber below also needs work. Depending on the method and scope, Karo provides a warranty of up to 10 years on rehabilitation work.
A typical case from our service area: at an apartment building in the canton of Zurich, the forecourt is being repaved so that cars can park there in future. In the area there is a round inspection chamber with a lightweight plastic cover of class A15, which would sit around eight centimetres too low after the redesign. Instead of simply paving over the cover, the chamber is first cleaned and checked with the camera. This reveals a cracked chamber neck. As part of a manhole rehabilitation, the neck is repaired, brought up to the new level with an adjustment ring, and a cast iron cover of class B125 is reset in mortar – suited to the new use as a parking area. The cover remains visible and freely accessible.
