What does the SN EN 13508-2 standard govern?
The EN 13508 series of standards bears the title «Investigation and assessment of drain and sewer systems outside buildings». Part 1 describes general requirements for condition recording, Part 2 the «Visual inspection coding system». Switzerland has adopted the European standard, hence the prefix SN for Swiss standard (Schweizer Norm). The text of the standard corresponds to the European version, which also applies in Germany and Austria; how the codes are applied and evaluated in detail is supplemented by the countries with their own guidelines, in Switzerland with those of the VSA.
The standard does not determine how good or bad a pipe is. It only governs how what the camera shows is described: which code is used to name a defect, how its size is stated, where it lies on the pipe circumference and at what point in the pipe it begins and ends. Only this uniform language makes it possible for an inspection carried out today by one specialist company to be read, evaluated and compared with a new survey in ten years' time by another specialist company or an engineering firm.
Without coding, a report might say «crack in the pipe, fairly large» or «some roots». With coding, it contains a precisely defined code with a measured value and position. This is less vivid, but unambiguous, and that is exactly what matters when municipalities, insurers or buyers make decisions about rehabilitation and costs.
How a code is structured
Every observation begins with a three-letter main code. The first letter indicates where the observation was made: B stands for the pipe, D for the manhole or inspection chamber. The second letter assigns the observation to a group: A for structural features, i.e. damage to the pipe itself, B for operational features such as deposits or roots, C for inventory data such as connections or bends and D for other information, for example an abandoned inspection. The third letter designates the specific observation.
Depending on the observation, the main code is supplemented by up to two characterisations that describe the finding in more detail, for example whether a crack runs longitudinally or circumferentially, or whether a joint has been displaced longitudinally, radially or angularly. In addition, there is a quantification, for example a crack width in millimetres, a displacement in millimetres or a reduction in cross-section as a percentage.
The position on the pipe circumference is given according to the face of a clock: 12 o'clock is the crown, i.e. the top of the pipe, and 6 o'clock is the invert, along which the wastewater flows. Root ingress «from 11 to 1 o'clock» is therefore at the top of the pipe, and a deposit «from 5 to 7 o'clock» is on the invert. The position along the pipe is given in metres from the starting point of the survey. If damage extends over a longer distance, the start and end are marked as a continuous defect instead of repeating the same finding metre by metre.
Examples of main codes in the pipe
Among the structural features (BA), the most common codes include: BAA for deformation, i.e. a pipe that is no longer round; BAB for cracking; BAC for a break or collapse; BAF for surface damage, for example due to corrosion or abrasion; BAG for an intruding connection that protrudes into the main pipe; BAH for a defective connection; BAI for intruding sealing material, for example a sealing ring that has been pushed out; and BAJ for a displaced joint.
Among the operational features (BB), the main codes are BBA for roots, BBB for attached deposits such as encrustation or grease on the pipe wall, BBC for settled deposits on the invert, BBE for other obstacles and BBF for infiltration, i.e. groundwater entering the pipe. Inventory data (BC) record what belongs to the pipe and is not damage, for example BCA for a lateral connection. Other information (BD) documents, among other things, general remarks or the fact that an inspection had to be abandoned, for example because the camera could not get past an obstacle.
For manholes, there is a parallel series of codes beginning with D. This means that cracks in the manhole wall, defective step irons or intruding pipes in a manhole can be recorded using the same logic as the findings in the pipe.
Coding and VSA condition grades: two separate steps
A common misunderstanding: SN EN 13508-2 does not award grades. The standard describes the finding; it does not assess it. Assessment is deliberately regulated at national level, because climate, soils, pipe materials and legal frameworks differ from country to country. In Switzerland, it is carried out in accordance with the requirements of the Swiss Association of Wastewater and Water Protection Professionals (VSA), which are based on the guideline «Maintenance of sewer systems».
The condition grade is derived according to fixed rules from the coded individual findings of a pipe run, i.e. a pipe section between two manholes. The VSA scale runs from 0 to 4: grade 0 means collapsed or at acute risk with immediate need for action, grade 4 a pipe without relevant damage. As a rule, the most serious finding determines the grading of the entire pipe run.
For owners, this means: the quality of the condition grade depends directly on the quality of the coding. If a longitudinal crack is recorded as harmless surface damage or a displacement is measured too small, the grade will be too good, and necessary rehabilitation will be postponed. Conversely, coding that is too strict leads to unnecessary costs. Clean coding that complies with the standard is therefore the basis of every fair condition assessment.
What the inspection report contains
At its core, an inspection report in accordance with SN EN 13508-2 consists of two parts. The header contains the master data of the pipe run: location, start and end point, direction of inspection with or against the direction of flow, pipe material, profile, nominal diameter, date and the person who carried out the survey. This is followed by the observation log, in which every finding is listed with its position in metres, code, characterisation, quantification and position on the circumference, usually supplemented by a still image of the spot.
In addition, there is usually a graphical representation of the pipe run with all findings along the pipe and the video recording of the entire survey. If a condition assessment is then prepared, it adds the condition grade of each pipe run to the report, together with recommendations as to which measures make sense and in what order.
Because the codes are internationally uniform, the data can be transferred to drainage registers and planning programs. In Switzerland, the VSA provides its own data model for exchanging inspection data. Municipalities and engineering firms can thus import findings directly into their utility data and into the general drainage plan, instead of retyping reports.
Why municipalities, managers and buyers pay attention to the standard
Municipalities can require owners to provide proof of the condition of private wastewater pipes, for example in the case of conversions, new connections or when the public network is being rehabilitated as part of the general drainage plan (GEP). The requirements are set by the respective municipality. What is needed is documentation that records the finding in a traceable and comparable way; a freely worded report or a video without a log can lead to follow-up questions.
For property management companies, coding that complies with the standard is a planning tool: repeated surveys of the same pipe a few years apart can be compared code by code. This shows whether a crack is getting bigger, whether roots are growing back or whether a finding is stable, and rehabilitation work can be prioritised and budgeted across several properties.
For buyers of a property, a coded report is above all a basis for negotiation. It shows objectively what condition the underground drain and house connection are in and can be checked by an independent specialist company or an engineering firm. Anyone who has a CCTV drain survey with coding carried out before buying can realistically estimate any rehabilitation costs instead of discovering them after the keys have been handed over.
How Karo Kanaltechnik documents in accordance with SN EN 13508-2
At Karo Kanaltechnik, every CCTV drain survey is documented in accordance with SN EN 13508-2. Where deposits block the view, the pipe is cleaned before the survey, without chemicals, using high-pressure water jetting at up to 200 bar, so that nothing conceals any damage. The pipe is then surveyed with the camera, possible from DN 50, and every finding is recorded with its code, measured value and position.
For the camera survey, Karo adds a surcharge from CHF 50 to the hourly rate of CHF 160 and the call-out fee of CHF 60 (all prices excl. VAT). Anyone who also needs an assessment, for example for the municipality or before a purchase, receives a grading according to the VSA condition grades with the condition assessment, together with a recommendation for how to proceed, from a check survey in a few years' time to trenchless rehabilitation.
A typical case from the Zurich Oberland: owners are planning an extension to an older single-family home. For this, the municipality requires proof of the condition of the existing underground drain up to the house connection. Karo Kanaltechnik first clears the pipe with high-pressure jetting and then surveys it with the camera. The report in accordance with SN EN 13508-2 then lists, among other things, a displaced joint (code BAJ) with its position in metres and root ingress (code BBA) at a joint, each with its position on the pipe circumference and a still image. The municipality can follow the report, and the owners know at which spot localised rehabilitation is needed, instead of replacing the entire pipe on suspicion.
