What is light well drainage?
A light well is the open shaft in front of a basement window that brings daylight and air into rooms below ground level. Because it is open at the top or only covered with a grating, every raindrop that hits the grating falls straight to the bottom of the well. On top of that comes water that runs down the facade or, in heavy rain, flows into the well from the adjacent surface.
So that this water does not stand, a drain is built into the floor of the well – usually a small floor drain with a grating or strainer, and in older houses often just an open pipe opening. From there, a pipe carries the water away. All of this together, i.e. the drain, the connecting pipe and the pipe it joins, is called light well drainage. It is part of the private property drainage and is therefore the owner's responsibility.
Light well drainage is small, but it sits at the lowest point of the facade, directly below a window. If it fails, there is no buffer: if the water in the well rises above the window sill, it runs into the basement.
Where does the drain in the light well lead?
Where the water from the light well flows depends on when the property was built and on the municipality's drainage concept. The drain is often connected to the drainage pipe that runs around the foundations and collects seepage water. Just as common is a connection to the rainwater pipe, which also takes the roof water. In some houses, the pipe ends in an infiltration system in the garden.
In older buildings with a combined system, the light well was sometimes connected directly to the foul water or combined sewer pipe. This is risky, because sewer water can push back through precisely this drain when the system is overloaded. Where the separate system applies, clean rainwater does not belong in the foul water pipe; the Waters Protection Act requires unpolluted rainwater to be allowed to soak away wherever possible.
Which option applies to your house is shown in the property's drainage plan. If it is missing or no longer accurate, the route can be traced from the light well with a small drain camera and a locating sonde.
Why does the light well drain become blocked?
The light well is a natural trap for everything the wind carries across the ground. Leaves, pine needles, pollen, seeds and soil collect on the floor of the well, get wet and form a dense, sludgy layer. This layer settles on the drain grating and seals it like a lid. On top of that there is litter, cigarette ends and occasionally dead animals that fall through the grating and cannot get out again.
A second problem lies deeper: fine sand and soil get past the grating into the connecting pipe and settle there. If the pipe joins a drainage pipe that is itself already silted up or narrowed by root ingress, the water drains only slowly even when the grating is clean. From above you then see a clear drain, but the water still stands.
Typical signs are a puddle that stands in the well for days after rain, a musty smell, rings of algae or sludge on the walls of the well and damp patches below the basement window. At the latest then, the drain should be cleaned, before a thunderstorm makes the problem visible.
Water in the basement during heavy rain: light well or backflow?
If water runs through a basement window during heavy rain, there are two fundamentally different causes. The first: the drain is blocked or too small for the quantity of water that falls into the well in a short time and flows in from the surroundings. The water then rises from above, is usually clear or muddy and comes from the well itself.
The second cause is backflow. If the pipe to which the light well is connected is overloaded during heavy rain, water pushes backwards through the drain into the well. This happens particularly with light wells whose floor lies below the backflow level – i.e. below the level to which the water in the sewer system can rise, usually the road surface. If the pipe is connected to foul water, the water flowing back is correspondingly dirty and smells.
The distinction matters because the measures are different. For a blockage, cleaning and regular checks help. For backflow, cleaning alone does not help; what is needed is suitable backflow protection, a modified connection or, for low-lying wells, a lifting station. Whether water came from above or was pushed back from below can usually be narrowed down well with a camera inspection of the connecting pipe.
How Karo cleans the light well drain
First the well itself is cleared: leaves, soil and sludge are removed from the well by hand or with the suction hose so that none of it is flushed into the pipe. Then the drain grating is removed and cleaned.
Then comes the pipe. Depending on the diameter and condition, the team uses a jetting nozzle for chemical-free high-pressure water jetting at up to 200 bar or breaks up firm plugs mechanically with the drain snake. Jetting continues into the pipe to which the light well is connected. If that is a drainage pipe or a rainwater pipe with a silt trap, it makes sense to clean these parts at the same time, because the light well only drains as well as the pipe behind it.
Finally, the drain is tested with water: if a larger quantity drains away without backing up, the light well drainage is working again. If the water stands or there are indications of damage, a camera inspection follows.
Camera inspection of the connecting pipe
Many light well pipes are only a few metres long, but they run under the ground, the foundations or the basement floor and cannot be seen. With a CCTV camera, the pipe is surveyed from the drain. The images show where the pipe actually leads, whether it is broken, displaced, sagging or has roots growing in, and whether it is correctly connected to the drainage pipe or rainwater pipe.
Karo documents the findings in accordance with SN EN 13508-2. This makes it possible to judge properly whether cleaning is enough, whether a section of pipe has to be repaired or whether the cause of recurring water in the basement lies elsewhere – for example in silted-up drainage or missing backflow protection. Such a finding is also helpful when the cause has to be established after water damage.
What does it cost to clean a light well drain?
Karo charges by time: CHF 160 per hour plus CHF 60 call-out fee, each excl. VAT. One hour of work including call-out therefore comes to CHF 220 excl. VAT or CHF 237.82 incl. 8.1% VAT. For a camera inspection, a CCTV surcharge from CHF 50 is added. A typical job at a single-family home is usually CHF 150–400, depending on the number of light wells, the condition of the pipes and accessibility.
It pays to combine several jobs: all light wells, the roof water drains and the drainage pipe in a single visit. The call-out fee is then only charged once, and the whole rainwater system is in the same condition.
Prevention: keeping the light well clean
You can prevent most blockages yourself. Look into every light well at least in spring and in autumn after the leaves have fallen, remove leaves and soil and clean the drain grating. After heavy thunderstorms, it is worth taking a quick look to see whether the water has drained away.
A fine-mesh cover or leaf guard over the grating keeps leaves and small animals out without blocking the light. The rim of the light well should be slightly above the surrounding ground so that surface water does not run straight in during heavy rain; with sloping driveways or on hillsides, an upstand or a channel in front of it can make sense. These are structural questions for a builder to assess.
For the pipe itself: if a light well regularly has standing water despite a clean grating, the problem lies in the pipe or behind it. Then jetting with a camera inspection makes more sense than repeatedly bailing it out.
A typical case from our service area, as it occurs in older single-family homes in the Zurich Unterland: after every heavier rainfall, water stands in the light well in front of the laundry room, and after a summer thunderstorm it runs over the window sill into the basement. The drain grating is stuck together with wet leaves, and below it the connecting pipe is filled with sand and soil. The well is cleared, the pipe is jetted at high pressure and inspected with the camera. If the survey shows that the light well is connected to a drainage pipe that is itself silted up, this is jetted at the same time – only then does the water drain freely again. For the future, a fine-mesh leaf guard over the grating and a check every autumn help.
