GlossaryDrainage technical term

Leak (leakage)

Also: Leakage, Lack of tightness, Leaking point, Leak point

A leak is a point in a pipe, chamber or tank that is not watertight, through which water or wastewater escapes or gets in unintentionally. It often stays invisible for a long time – and that is precisely why it damages the building fabric, the soil and the groundwater.

Proving a leak: pressure gauge and test equipment for the pressure and leak-tightness test of a pipe

In brief

A leak is a point in a pipe that is not watertight, through which water escapes or gets in unintentionally. In wastewater pipes, wastewater seeps into the ground or groundwater gets in; in drinking water pipes, pressurised water is lost. Signs are damp walls, odours, subsidence and rising water consumption. It is found with leak detection, a leak-tightness test and a CCTV drain survey.

What is a leak?

The term leak refers to any lack of tightness in a system that ought to be watertight. In buildings and in the sewer network, it is almost always about pipes: drinking water, heating and wastewater pipes, plus chambers, separators and pits. The leak is the condition or damage itself, i.e. the hole, the crack or the open joint. The process used to search for this point is called leak detection.

Leaks rarely appear all at once. Usually it starts with a small weak point, such as an aged joint seal, a hairline crack or a spot of corrosion, and the leak grows over months or years. Because most pipes lie in walls, under floors or in the ground, you almost never see the leak itself, only its consequences.

Typical causes are ageing of the pipe material, shifted pipe joints (displaced joints), roots that have grown in, settlement of the ground, loads from traffic, frost, chemical attack from aggressive wastewater and installation errors. In older properties there are also brittle materials such as vitrified clay without elastic seals, or asbestos cement, which develop cracks and fragmentation over the years.

Leaks in wastewater and drinking water pipes: the difference

Drinking water and heating pipes are under pressure. If such a pipe leaks, water escapes continuously, even if nobody opens a tap. This usually shows up quickly: the reading on the water meter keeps rising, the pressure in the heating system drops, and wet patches appear on the wall or ceiling. A leak in a pressure pipe is therefore often an acute water damage incident.

Wastewater pipes, by contrast, usually work by gravity: the water flows away along a gradient and without pressure. A leak here is quieter and goes unnoticed for much longer. A little wastewater seeps into the ground every time the pipe is used, or groundwater pushes into the pipe from outside when levels are high. Because no pressure drops and no water meter registers anything, the damage is often only noticed during a camera inspection, a leak-tightness test or through consequential damage.

This difference is crucial for locating the leak. With pressure pipes, acoustic methods, correlation measurement and tracer gas help, because escaping water makes noise and gas can be traced. With wastewater pipes, the CCTV drain survey shows the damage from the inside, and the leak-tightness test proves whether a pipe run is tight or not.

Exfiltration and infiltration: water out, water in

With leaking wastewater pipes, a distinction is made between two directions. Exfiltration means that wastewater escapes from the pipe and seeps into the ground. This pollutes the soil and groundwater with contaminants, nutrients and germs. Under the Waters Protection Act (GSchG), the owners of wastewater installations must therefore operate, service and maintain them properly, and that includes the pipes being watertight.

Infiltration is the reverse: if the pipe lies in groundwater or in wet soil, clean water gets into the pipe through the leak. This unwanted water is called infiltration water. It fills the sewer system, dilutes the wastewater and has to be treated unnecessarily in the wastewater treatment plant as well. For the municipality this means higher operating costs, and for the owner possibly a demand to carry out rehabilitation.

Often both directions occur at the same point, depending on the groundwater level. The water that gets in also washes sand and fines from the surroundings into the pipe. This creates voids next to the pipe, which weaken the pipe bedding and lead to further damage.

Signs of a leak

A single sign does not prove a leak, but several together are a clear indication. Pay particular attention to damp or stained walls and floors, peeling paint, efflorescence and mould, especially in the basement and along pipes.

Other warning signs are a musty smell or sewer smell in the basement or garden, water consumption that rises for no apparent reason, a water meter that keeps counting with the taps closed, and heating pressure that has to be topped up again and again.

Outside, subsidence in the lawn, the paving or the asphalt above the pipe points to washed-out soil. Conspicuously green strips of lawn in summer, roots that grow specifically towards the pipe, and recurring blockages at the same point can also be connected with a leak. Roots usually get in where a joint is already leaking.

What are the consequences of an undetected leak?

The longer a leak goes unnoticed, the more expensive it becomes. In the building, escaping water soaks insulation, screed and masonry. Mould, structural damage and odours develop, and drying out often takes weeks. A small leak thus turns into major water damage.

With buried wastewater pipes, the water escaping or getting in washes fine material out of the pipe bedding. Voids form, the pipe loses its support, and further displacements, cracks and, in the worst case, a pipe collapse follow. On the surface this later shows up as subsidence or even a cave-in.

There are also environmental and legal consequences: escaping wastewater pollutes the soil and groundwater, and infiltration water getting in burdens the public sewer system. Municipalities can demand rehabilitation during inspections or as part of drainage planning. And not least, every week without a repair lengthens the list of damage that an insurer has to assess.

How to find a leak

The first step is narrowing it down: which pipe is affected – pressure pipe or wastewater, inside or outside? The water meter, the heating pressure, the property's drainage plan and the location of the damp patches all help here.

With pressure pipes, actual leak detection comes into play: acoustic locating and correlation measurement listen for the escaping water, supplemented if necessary by tracer gas or thermography. This usually allows the leak to be pinpointed to within a few centimetres without having to break anything open first.

With wastewater pipes, the pipe is first cleaned at high pressure so that the camera has a clear view. The CCTV drain survey then shows cracks, displacements, open joints, root ingress and water getting in, and the findings are coded in accordance with SN EN 13508-2. The leak-tightness test with air or water, carried out according to the test methods of SN EN 1610, then proves whether the pipe run is tight. For incorrect connections and leaks that are hard to find, a smoke test also helps.

Fixing a leak: repair and rehabilitation

Which measure is suitable depends on the type, number and location of the damage. A single leaking joint or a single crack in a wastewater pipe can usually be sealed trenchlessly with a patch liner (Pointliner): a resin-impregnated sleeve is moved to the damaged point, pressed against the wall and cures there.

If a pipe has many leaks along its entire length, a CIPP liner is more economical. It forms a new, seamless pipe inside the old pipe and seals the whole pipe run in one go. Only where a pipe has collapsed, is badly deformed or has been laid incorrectly is replacement by open-cut construction required.

After every rehabilitation, a final camera inspection shows that the work has been carried out properly; if necessary, a leak-tightness test proves that the pipe is tight. Karo gives a warranty of up to 10 years on rehabilitation work, depending on the method and scope. Leaks in drinking water and heating pipes inside the building are usually repaired by the plumber or heating engineer once the point has been located.

Practical example

In an apartment building in the canton of Zurich, there is a recurring musty smell in the basement, efflorescence is forming on an outside wall, and a slight hollow has formed in the lawn in front of it. The water meter and heating pressure show nothing unusual, which largely rules out the pressure pipes as the cause. After high-pressure cleaning of the underground drain, the camera inspection shows two open joints with root ingress, exactly beneath the sunken spot. Both leaks are sealed trenchlessly with one patch liner each, the final inspection documents the result, and the garden does not have to be dug up.

Leak (leakage): frequently asked questions

What is the difference between a leak and leak detection?+

The leak is the point that is not watertight, i.e. the damage to the pipe, chamber or tank. Leak detection is the process used to search for this point and pinpoint it, for example with acoustics, tracer gas, thermography or a camera.

How do I recognise a leak in the wastewater pipe?+

Typical signs are damp basement walls, sewer smells, subsidence in the garden or in the paving above the pipe, and recurring blockages at the same point. A leak can only be proven reliably with a CCTV drain survey or a leak-tightness test.

How do I recognise a leak in the water pipe?+

Close all taps and watch the water meter. If it keeps counting, a pressure pipe is leaking somewhere. Other indications are wet patches on the wall or ceiling, unusually high consumption and heating pressure that drops regularly.

Is a small leak dangerous?+

Yes, because it grows and its consequences remain hidden for a long time. Even a little escaping water can soak insulation and masonry, cause mould or wash out the pipe bedding. The earlier the point is found, the smaller and cheaper the repair remains.

Does fixing a leak require digging?+

With wastewater pipes, usually not. Individual defects are sealed trenchlessly with a patch liner, and pipes that leak along their whole length with a CIPP liner. Digging is only needed if a pipe has collapsed, is badly deformed or has been laid incorrectly.

Who is responsible for a leak in the house connection?+

Pipes on your own plot are part of the private property drainage. The owner is generally responsible for keeping them watertight and maintaining them. Exactly where the boundary with the public sewer system lies is set out in the municipality's drainage regulations.

What does Karo charge to search for a leak?+

Work is charged by time: CHF 160 per hour plus CHF 60 call-out fee, excl. VAT. If a CCTV drain survey is added, a surcharge from CHF 50 applies. How long the search takes depends on the pipe, accessibility and the method.

Does insurance pay for a leak?+

That depends on the policy. Consequential damage caused by water from pipes is often insured, but the repair of the leaking pipe itself is not always covered. A documented finding with images and the exact location of the leak makes it considerably easier to clarify matters with the insurer.

Leak (leakage) in your region?

We are there for you across German-speaking Switzerland – fast, clean, with a 24/7 emergency service.